S/V Deep Playa - Pearson 424

When it comes to list it’s important to remember that length doesn’t matter as much as the magnitude of the accomplishment. Here are today’s magnum sized check marks:

• Porthole installed in the head and shower. This is the first wave the redo on the portholes. We completely pulled down the drip rail and interior paneling, put up new paneling and (done before today) and installed the portholes with an interior teak ring that allows them to fit better. This was a bigger PITA than planned because one of the “matching” teak trim pieces needed about 3 hours of sanding to fit its matching porthole.
• Lowered the dinghy from the rafters at the workshop, carted it down to the marina, pumped it up and cleaned it. Dawn took it on a test row and look especially cute doing so!
• Re-installed the swim ladder. Dawn had some ambitious plans to add teak steps to it, but with the plan to eventually install a wind vane on the stern that didn’t make much sense. We did clean it up though and it looks a lot better.
• Finally finished off the horrible Ballard organics hand soap which left residue on everything and everyone.
• Rain and poor attitude lead to a two hour rain delay at Ray’s. don’t’ order that blend they’re offering by the glass. It’s nasty; I sent it back. Just order a bottle of the 2007 Sharecropper’s Cabernet $30 and easy peasey (no offense Susan).
• Watched at least 8 firework shows from Golden Gardens. What a great way to wrap up another great day!

Both sides of this used to look like the right side. A little stainless steel wire brush action with the Dremel and we're approaching nautical beauty. Do you own a boat? Go buy a Dremel tool !

I love to update the blog with checkboxes as we go. Feels good to celebrate the wins and document our progress. As you know we’re working toward stepping our masts on Thursday 24 June.

I got all the pins from Andersen Machine Shop in Port Townsend and they were beautiful. Had a slight mishap with them last week because I put in an incorrect dimension (too long) for some of the pins, but with PT all mail is basically overnight so we were able to send them back have them cut down and get them back in 2 days! I highly recommend Andersen Machine Shop. Olaf is a very nice guy and was very helpful. He made our pins on his CNC machine, they look awesome.  With pins in hand I was able to attach all of the rigging to the masts! I did all that in the pouring “Junary” rain we’re experiencing in Seattle this summer so no pics yet.

On the boat Dawn has been working on the ash battens to line the aft berth, v-berth and open lockers.

First she’s lining all our lockers with Reflectix Insulation  which looks like aluminum foil bubble wrap. We’re laying it in loose along the hull NOT gluing it down. We don’t ever want to have to scrape the hull for a month again. The insulation will keep a tad warmer here in Seattle and a tad cooler in the Tropics. It’s pretty cheap, you can get it at Home Depot and its easy to work with.

Here’s what the battens look like when they are installed. Dawn as always does gorgeous work when I stay out of the way. ;-)

The only thing left to do before we step the masts on Thursday are to install the mast steps and make some leather grommets for the wiring exits on the main mast. After that I’ll remount the booms and winches along with a couple other things. Right after we tune the rig we should be able to sail again!

I called the yard and set the date for re-stepping the masts ! By this time next week we should have the rig back up !

Before

• The chainplates were previously pulled and cleaned up with a Scrotchbrite pad and water.
• They were then polished by sanding with progressively finer grades of sand paper starting at 120 grit and going up to 1200 grit.
  
•   
  Plates were then dry fitted and marked with tape so we knew how thick the desk was and where to apply the butyl.
  
•  
  Butyl rope caulk which we got from New Found Metals when we purchased our potlights was wrapped around the chainplate and then it was inserted into the deck again and through bolted. The butyl you see sticking out here was pushed down into the deck.
  
•  
  The chainplate covers were then placed down with 3M 4200 and screwed into place.

We’ve had some really good rain and no leaks through the chainplates. The chainplates were previously hidden behind teak enclosures, we plan to leave them open so we can inspect them and notice any issues sooner. Plus look how shiny they are !! Dawn did most of the work on this one, I only did some late night sanding. Did I mention how awesome she is?